Where do you drill holes in ice fishing?

What kind of ice auger is best?

What size ice auger is best? For gas or electric augers, choosing the largest you can afford is usually your best bet. Ten-inch is the most common size and will tackle every situation or species you may target. A 4 1/2 inch hand auger is perfect for chasing panfish during early ice.

Will any drill work for ice auger? Unless you’re using a heavy-duty drill or are unsure of your grip, you’re fine with just using the drill for 6-inch augers. I simply get a good grip on the drill and hold the back of the drill tight with my free hand. But a stabilizing handle isn’t a bad idea for 8-inch models because of increased torque.

Is a 6 or 8 ice auger better? If your going with the hand auger I would recommend the 6 . Its alot easier to punch a bunch of holes with the 6 . Depending on the amount of ice you chew through a season,the 8 inch I always had the replace twice a year. The 6 inch cut better and I went through a set of blades in about a season and half.

How do you sharpen ice auger blades?

Where do you drill holes in ice fishing? – Related Questions

What is the fastest ice auger?

As far as we can tell, the Trophy Strike 120V Lithium Ion Ice Auger is the fastest ice auger in the world!

Is 6 auger big enough?

I’m content with the 6. Unless your purposely targeting trophy fish a 6 inch hole is plenty especially if you only target panfish. With over 18 inches in diameter when’s the last time you pulled a fish larger than 18 inches in diameter through the ice.

How deep are ice fishing holes?

The hard part is finding them. Many hardwater anglers spend far too much time fishing over deep structure-underwater points and reefs in the middle of the lake in 80 to 100 feet of water. Instead, it’s much wiser to drill holes over and around structure in moderately deep water of 20 to 40 feet.

How far apart should ice fishing holes be?

Here’s the quick answer: If you’re fishing next to someone else on the ice, your holes should be at least 5-6 feet apart to avoid fish getting tangled in each other’s lines when you pull them up. If you’re using a camera for ice fishing, the hole for the camera should be at least 2 feet away from your fishing hole.

How much torque do you need for a drill ice auger?

Re: Hand Drill Auger Ice Torque Requirement The general recommendation is 700 in/lbs or better brushless drill…

Can you use a hammer drill for an ice auger?

What’s the best drill to use for ice fishing?

How do you use a hand auger?

How much does it cost to sharpen ice auger blades?

Triple Grind Process $29.95 Your cost is $19.95 per set. Select from the drop-down box below. If you are sending in one Jiffy or Strikemaster chipper-style blade, the cost is $13.95. For the rare, Strikemaster Ultramag 9″, 3-Blade Set, cost is $19.95 The Jiffy STX, three blade set is also $22.95.

Can you sharpen auger blades with knife sharpener?

A variety of tools and methods can be employed to sharpen ice auger blades. A blade that has been badly damaged or rusted might first need some attention with a wood or metal file. You can use a whetstone or knife sharpener for precise honing.

How do you sharpen auger blades with sandpaper?

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

Do electric drill ice augers work?

What size auger do you use for a 4×4 post?

Post Holes- If you plan to secure your posts with cement or by tamping dirt, you will need spacing around the post to do so. For example: A 4×4 post (actual size 3.5″x3. 5″) has a maximum width of just over 5″ (diagonally). Therefore, the 4×4 post will likely fit into a hole drilled by a 6″ diameter auger.

How big of a hole do you need for a 4×4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter.

How is auger bit measured?

A) Measure the distance between the opposite side of the screw point at its base and the outer edge of cutting lips (D1). B) Measure the thickness of the screw point at the base (D2) C) Subtract 1/2 of the (D2) measurement from (D1) to obtain radius (D) of the bit.

What is the best month to ice fish?

March is my favorite month for ice-fishing. The days are longer, the weather isn’t as cold, and the fish like to get caught in March. Following are some things to keep in mind to catch more fish through the ice until the end of the ice season.

Is it better to ice fish in shallow or deep water?

For the most part, where you find the fish in the spring and fall will be the same place you’ll find them in the winter. In my experience, I’ve found that most of the best ice-fishing action comes in water from 3-to-20 feet deep.

What time of day is good for ice fishing?

The best time of day to ice fish is during the first couple of hours after sunrise, and for about 2 hours both before and after sunset. These are the times when most fish are heading to their feeding grounds, and when most species are active.

How do you attract fish while ice fishing?

What does every ice fisherman need?

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

Will an ice auger work on dirt?

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

What kind of oil does a jiffy propane auger use?