What is the best month to ice fish?

March is my favorite month for ice-fishing. The days are longer, the weather isn’t as cold, and the fish like to get caught in March. Following are some things to keep in mind to catch more fish through the ice until the end of the ice season.

Is an 8 inch ice auger big enough? Ice fishing holes range in size from 6 to 12 inches in diameter. The ideal hole size is 8 inches. An 8 inch hole is big enough to pull most fish through while also being easy enough to drill with a hand powered ice auger.

Is a 6 or 8 ice auger better? If your going with the hand auger I would recommend the 6 . Its alot easier to punch a bunch of holes with the 6 . Depending on the amount of ice you chew through a season,the 8 inch I always had the replace twice a year. The 6 inch cut better and I went through a set of blades in about a season and half.

What size ice auger should I get? For gas or electric augers, choosing the largest you can afford is usually your best bet. Ten-inch is the most common size and will tackle every situation or species you may target. A 4 1/2 inch hand auger is perfect for chasing panfish during early ice.

What kind of ice auger is best?

How big of a fish can fit through a 6 inch hole? 6 inch hole is 18.85″ in circumference. A 28″ walleye of about 18″ girth is almost a 12 pound fish. A 36″ northern 18″ around is a 13 pound fish. 6 inch hole is fine for all walleye and pike except the trophies.

What is the best month to ice fish? – Related Questions

How deep are ice fishing holes?

The hard part is finding them. Many hardwater anglers spend far too much time fishing over deep structure-underwater points and reefs in the middle of the lake in 80 to 100 feet of water. Instead, it’s much wiser to drill holes over and around structure in moderately deep water of 20 to 40 feet.

How do you use a hand auger?

How do you measure auger size?

Outer diameter is equal to the shaft diameter plus twice the strip width (inside edge to outside edge) of the flighting.

How do you measure an ice auger?

What is this? You can always use a tape measure to double-check the markings left on your auger. You’ll do this by hooking the metal edge of the tape measure to the bottom of your hole. If the marking reads four inches (10.16 centimeters) or more then you should be safe to begin fishing.

How do you cut holes for ice fishing?

How do you sharpen ice auger blades?

What is the fastest ice auger?

As far as we can tell, the Trophy Strike 120V Lithium Ion Ice Auger is the fastest ice auger in the world!

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

Is it better to ice fish in shallow or deep water?

For the most part, where you find the fish in the spring and fall will be the same place you’ll find them in the winter. In my experience, I’ve found that most of the best ice-fishing action comes in water from 3-to-20 feet deep.

What time of day is good for ice fishing?

The best time of day to ice fish is during the first couple of hours after sunrise, and for about 2 hours both before and after sunset. These are the times when most fish are heading to their feeding grounds, and when most species are active.

How hard is it to use a manual ice auger?

Are manual ice augers hard to use? A manual ice auger with sharp blades easily cuts through 6-8 inches of ice like butter in under 10 seconds. Drilling a hole in ice 10-18 inches thick using a hand auger is significantly harder and will take at least 30 seconds of hard work for each hole.

Do hand ice augers work?

They work fine on early ice that is less than 10 inches thick, but once the ice gets thicker they become a drag to use. If you only plan to drill one or two holes no problem, but most of us with power augers like to cut more than that during a day.

Do drill ice augers work?

Don’t push on the auger, let it pull itself through the ice. Clean out the hole frequently—drill-powered augers work great, but on thick ice, the drill motor can get bogged down by pushing lots of ice shavings up out of the hole.

Which way do you rotate an auger?

Certain stoves need the auger motor to be set up for clockwise rotation (CW) while other need to be set up for counterclockwise rotation (CCW). If you turn the auger by hand without the auger motor, then you can tell which direction to set the motor in order to push pellets into the auger chute then the burn pot.

How do you make an auger?

What is auger pitch?

Auger pitch refers to the distance between corresponding points on consecutive turns of the auger flighting or the distance the conveyed material moves with one revolution of the auger. Most augers are standard pitch with pitch approximately equal to the auger diameter.

How thick should ice be for ice fishing?

Once you have the proper tools and safety gear for fishing on the ice, consider these general safe ice fishing, or safe ice thickness guidelines. Stay off of any ice that is 3 inches or less thick. Remember that a minimum of 4 inches of clear, solid ice is a requirement to support an average person’s weight.

How much ice do you need to hold a truck?

According to the Department of Natural Resources, 12-15 inches of solid ice is needed to safely drive a truck onto a lake or pond. 8-12 inches is needed for normal passenger vehicles. For snowmobiling, a minimum of 5 inches is recommended.

How thick should ice be?

Guide to Safe Ice Thickness Less than 4 inches: Stay off the ice. 4 inches: Walking, ice fishing, ice skating, or other activities on foot are permitted. 5 to 7 inches: Snowmobiling or riding ATVs are safe. 8 to 12 inches: Driving a car or small pickup is allowed.

Will an ice auger work on dirt?

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

What kind of oil does a jiffy propane auger use?

How much does a jiffy propane auger weight?

Weight: 8″ weighs 34 lbs., 9″ weighs 35 lbs., 10″ weighs 36 lbs.