What does every ice fisherman need?

There are 9 essential items that every angler needs on their ice fishing gear list:

• Jigging ice fishing rod and reel.
• Live bait container stocked with live bait.
• Terminal tackle such as line clippers, fish grabbers, pliers, hooks, sinkers, etc.
• Ice fishing tip ups.
• Ice fishing electronics.
• Ice augur and skimmer.

More items…

Is a 6 or 8 ice auger better? If your going with the hand auger I would recommend the 6 . Its alot easier to punch a bunch of holes with the 6 . Depending on the amount of ice you chew through a season,the 8 inch I always had the replace twice a year. The 6 inch cut better and I went through a set of blades in about a season and half.

What size ice auger is best? For gas or electric augers, choosing the largest you can afford is usually your best bet. Ten-inch is the most common size and will tackle every situation or species you may target. A 4 1/2 inch hand auger is perfect for chasing panfish during early ice.

What kind of ice auger is best?

Does Ion make a 6 inch auger? The ION cutting system features a Spot-On™ centering ring which allows you to re-open frozen holes. Together with the ION Straight-Through™ blade design, ION virtually eliminates “catching” at break-through saving you from jarring stops or yanks.

Is 6 auger big enough? I’m content with the 6. Unless your purposely targeting trophy fish a 6 inch hole is plenty especially if you only target panfish. With over 18 inches in diameter when’s the last time you pulled a fish larger than 18 inches in diameter through the ice.

What does every ice fisherman need? – Related Questions

Is a 6 inch hole good for ice fishing?

Ice fishing holes range in size from 6 to 12 inches in diameter. The ideal hole size is 8 inches. An 8 inch hole is big enough to pull most fish through while also being easy enough to drill with a hand powered ice auger. Again, there are several situations in which one size hole is better than another.

How deep are ice fishing holes?

The hard part is finding them. Many hardwater anglers spend far too much time fishing over deep structure-underwater points and reefs in the middle of the lake in 80 to 100 feet of water. Instead, it’s much wiser to drill holes over and around structure in moderately deep water of 20 to 40 feet.

What is the fastest ice auger?

As far as we can tell, the Trophy Strike 120V Lithium Ion Ice Auger is the fastest ice auger in the world!

How far apart should ice fishing holes be?

Here’s the quick answer: If you’re fishing next to someone else on the ice, your holes should be at least 5-6 feet apart to avoid fish getting tangled in each other’s lines when you pull them up. If you’re using a camera for ice fishing, the hole for the camera should be at least 2 feet away from your fishing hole.

How do you sharpen ice auger blades?

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

How do you keep auger batteries warm?

Whats better ion or strikemaster?

Not only do Ion augers drill faster, they are a tad bit smoother throughout the full cut. From tapping the hole to breakthrough, Ion bores a clean hole. Keep in mind though that StrikeMaster cuts reasonably fast and only looses by a small margin.

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

How much does a strikemaster ice auger weigh?

What size auger do you use for a 4×4 post?

Post Holes- If you plan to secure your posts with cement or by tamping dirt, you will need spacing around the post to do so. For example: A 4×4 post (actual size 3.5″x3. 5″) has a maximum width of just over 5″ (diagonally). Therefore, the 4×4 post will likely fit into a hole drilled by a 6″ diameter auger.

How big of a hole do you need for a 4×4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter.

How is auger bit measured?

A) Measure the distance between the opposite side of the screw point at its base and the outer edge of cutting lips (D1). B) Measure the thickness of the screw point at the base (D2) C) Subtract 1/2 of the (D2) measurement from (D1) to obtain radius (D) of the bit.

What is the best month to ice fish?

March is my favorite month for ice-fishing. The days are longer, the weather isn’t as cold, and the fish like to get caught in March. Following are some things to keep in mind to catch more fish through the ice until the end of the ice season.

Is it better to ice fish in shallow or deep water?

For the most part, where you find the fish in the spring and fall will be the same place you’ll find them in the winter. In my experience, I’ve found that most of the best ice-fishing action comes in water from 3-to-20 feet deep.

What time of day is good for ice fishing?

The best time of day to ice fish is during the first couple of hours after sunrise, and for about 2 hours both before and after sunset. These are the times when most fish are heading to their feeding grounds, and when most species are active.

Do electric drill ice augers work?

How much does a jiffy propane auger weight?

Weight: 8″ weighs 34 lbs., 9″ weighs 35 lbs., 10″ weighs 36 lbs.

What is the best auger for a drill?

How do you attract fish while ice fishing?

What is the best bait for ice fishing?

For ice fishing live bait, try wax worms (bee moth larva), maggots, spikes (fly larvae), wigglers (mayfly larvae) or minnows. You can drop your bait and leave it alone, or you can slowly jig to attract the fish. Ice fishing jigging also works with artificial ice fishing bait.

How do you measure an ice auger?

What is this? You can always use a tape measure to double-check the markings left on your auger. You’ll do this by hooking the metal edge of the tape measure to the bottom of your hole. If the marking reads four inches (10.16 centimeters) or more then you should be safe to begin fishing.

How much does a Strikemaster auger weigh?

How do you cut holes for ice fishing?