Under normal use, blades should be sharpened every 2 to 3 years. Blades must not have been abused drilling into rock, gravel, sand, etc, or until the blades can no longer be sharpened.
How long is the StrikeMaster Lite Flite?
| Brand | StrikeMaster |
|---|---|
| Manufacturer | StrikeMaster |
| Part Number | LFLD6 |
| Included Components | Lite-Flite Lazer Drill Unit 6″ |
| Size | 6 inch |
How do I contact StrikeMaster? Effective January 1, 2019 Customers should contact StrikeMaster Customer Service toll free at 877-572-7278 or [email protected] for a possible part replacement update at no charge for their Lithium Lazer (LL-8) auger.
How do you use a StrikeMaster auger?
How do you sharpen strikemaster ice auger blades?
How do you maintain a hand auger?
- Keep blade guard intact when auger is not in use to protect the cutting blades.
- After use, wipe blades dry with a cloth and spray a small amount of oil on cutting edge.
- Check and tighten blade screws before each use to avoid loss of blades due to vibrating during cutting of holes.
How long do ice auger blades last? – Related Questions
How do you start a strikemaster ice auger?
Can you hand sharpen ice auger blades?
Can you sharpen ice auger blades with a file?
A good blade edge will last a good long while if you allow it to. A variety of tools and methods can be employed to sharpen ice auger blades. A blade that has been badly damaged or rusted might first need some attention with a wood or metal file. You can use a whetstone or knife sharpener for precise honing.
How deep can you dig with a hand auger?
A hand auger can typically reach depths of up to 30 feet, while a power auger can go much deeper. Once the desired depth is reached, the auger is removed and a pipe is inserted into the hole.
How long does it take to drill a hole with a hand auger?
A manual ice auger with sharp blades easily cuts through 6-8 inches of ice like butter in under 10 seconds. Drilling a hole in ice 10-18 inches thick using a hand auger is significantly harder and will take at least 30 seconds of hard work for each hole. Avoid manual ice augers for ice thicker than 18 inches.
How do you clean an auger hole?
Wire wool or a stiff scrubbing brush will help you to remove soil from the auger blade and shaft. You may wish to use a hose or power washer to remove tougher dirt which has been caked onto the blade.
How do I start a new auger?
How do you start a strikemaster 24v?
QUICK START Unpack the 24v Battery Charging Base from carton and plug it in. Slide Battery onto Battery Charging Base using the channels on both sides as a guide. Press down until you hear it click in place. Leave Battery on Battery Charging Base until fully charged (Image 2).
How do you start a gas auger?
How do you sharpen ice auger blades with a stone?
How do you sharpen a post hole auger blade?
Can you sharpen K drill blades?
Yes, send us your dull auger blades and we will sharpen them for you for FREE!
How do you sharpen auger blades with sandpaper?
Can Jiffy ice auger blades be sharpened?
Jiffy actually makes a blade sharpener. And this is one that you can just put on a hard surface. They actually make little grippers on the back, but this is what looks like. And really all you do is put it on a hard surface, push down on it, take your blade and run it through this blade sharpener.
Can you sharpen Jiffy ripper blades?
How do you start an auger?
How do I start a new auger?
How do you start a flooded Eskimo ice auger?
With the unit resting on the ground, squeeze the throttle trigger to wide open throttle or fast position. At the same time the trigger is depressed, pull the starter rope several times, 10 to 15 times back to back. (Flooded engine will usually only take 6 to 8 pulls to get engine started.)
