How far apart should ice fishing holes be?

How far apart should ice fishing holes be?

Here’s the quick answer: If you’re fishing next to someone else on the ice, your holes should be at least 5-6 feet apart to avoid fish getting tangled in each other’s lines when you pull them up. If you’re using a camera for ice fishing, the hole for the camera should be at least 2 feet away from your fishing hole.

What size ice auger is best? For gas or electric augers, choosing the largest you can afford is usually your best bet. Ten-inch is the most common size and will tackle every situation or species you may target. A 4 1/2 inch hand auger is perfect for chasing panfish during early ice.

Is a 6 or 8 ice auger better? If your going with the hand auger I would recommend the 6 . Its alot easier to punch a bunch of holes with the 6 . Depending on the amount of ice you chew through a season,the 8 inch I always had the replace twice a year. The 6 inch cut better and I went through a set of blades in about a season and half.

What is the fastest ice auger?

Trophy Strike 120V Lithium Ion Ice Auger

As far as we can tell, the Trophy Strike 120V Lithium Ion Ice Auger is the fastest ice auger in the world!

What is the lightest ice auger? The new for 2019 ION G2 Auger weighs in at just 17 pounds. “It is the lightest, fastest, and longest-lasting electric auger on the market,” said Marshall. Even the previous electric auger models are more than 10 pounds lighter than the typical gas auger.

What is the best ice auger for the money?

  • Best Overall: Eskimo HC40 Propane Ice Auger at Amazon. …
  • Best Budget: StrikeMaster Mora Hand Ice Auger at Amazon. …
  • Best Gas: Jiffy 4G FourStroke Gas Ice Auger at Sportsmansguide.com. …
  • Best Electric: StrikeMaster Lithium 40V Electric Ice Auger at Amazon. …
  • Best Hand Auger: …
  • Best Drill Powered: …
  • Best Hand/Drill-Powered:

How far apart should ice fishing holes be? – Related Questions

What should I look for in an ice auger?

In addition to number of holes, the hole size should be considered in relation to the size of the fish you’re targeting. A hand auger is more suited to 4.5”, 6” or 8” inch holes, if you’re looking for bigger 10” holes (for larger fish like Lake Trout or Northern Pike) a hand auger isn’t recommended.

How big of a fish can fit through a 6 inch hole?

6 inch hole is 18.85″ in circumference. A 28″ walleye of about 18″ girth is almost a 12 pound fish. A 36″ northern 18″ around is a 13 pound fish. 6 inch hole is fine for all walleye and pike except the trophies.

How deep is an ice fishing hole?

4-6 inch ice depth = 6-8 inch hole. 6-18 inch ice depth = 6-10 inch hole. 18-24 inch ice depth = 8-12 inch hole.

How do you use a hand auger?

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

Do electric drill ice augers work?

How long does an ion ice auger battery last?

From the Ion FAQs page: “The battery is expected to last about 600-800 full charge cycles before performance will be affected.” If you exceeded that in two years, you must live pretty far north!

Where is K drill made?

the USA

Made in the USA, the K-Drill Ice auger is compact, lightweight, and durable. This coupled with a FREE blade re-sharpening policy makes K-Drill the ultimate ice auger for use with handheld cordless electric drills. Featuring tool steel chipper blades and compost flighting, this rugged 5lb.

Is Trophy strike still in business?

We now operate on a limited basis and no longer provide live phone responses. We apologize for the inconvenience. For business reasons, Frictionless World will no longer provide warranty and return authorization for Dirty Hand Tools, RanchEx, Vinsetta and Clam products.

How do you sharpen ice auger blades?

Will an ice auger work on dirt?

How much does a Strikemaster auger weigh?

15.9:1 Gear Ratio. Power Button with Deadman Safety Switch. Forward and Reverse. Built-in LED Lights….Limited 2-Year Manufacturer’s Warranty on Motor, Battery and Charger.
Model LFVL-8
Drill Size 10″
Weight 27 lbs.

3 more rows

How hard is it to use a manual ice auger?

Are manual ice augers hard to use? A manual ice auger with sharp blades easily cuts through 6-8 inches of ice like butter in under 10 seconds. Drilling a hole in ice 10-18 inches thick using a hand auger is significantly harder and will take at least 30 seconds of hard work for each hole.

Does Eskimo make an electric auger?

FREE SHIPPING IN U.S.

What kind of oil does a jiffy propane auger use?

Where do you drill holes in ice fishing?

How do you cut a hole in ice without an auger?

How do you cut a hole in ice without an auger?
Here is a quick list of all the methods I have seen used to successfully cut through ice without an auger.
  1. Axe.
  2. Spud bar.
  3. Digging iron.
  4. Pick axe.
  5. Chainsaw.
  6. Ice saw.

What is an ice fishing hole called?

What is an ice fishing hole called?

Suckerhole: A hole in the ice, caused by something that got stuck, like a stick. The sun heats the object, eroding the ice. On a recent day, one grew 3 inches in an hour, a guide said. Tip-up: Device used to suspend bait through your hole and detect when a fish strikes, without having to hold a fishing rod.

Do hand ice augers work?

They work fine on early ice that is less than 10 inches thick, but once the ice gets thicker they become a drag to use. If you only plan to drill one or two holes no problem, but most of us with power augers like to cut more than that during a day.

Is it hard to use an auger?

How hard is it to use a one-man auger? Harder than you might think, especially if the soil is rocky or made of heavy clay. Ergonomic handlebars designed to reduce vibration and fatigue help. But even when using a one-man auger, you may want a partner to help.

How do you snake past a 90 degree turn?

The proper way to use a snake is to insert the head into the drain and push very slowly without cranking. If you try to force it, it can bend back on itself and actually come out of the drain. Push gently and slowly, and if the auger is the right one for the job, it should slide smoothly through the pipe.

How much does a Strikemaster auger weigh?

15.9:1 Gear Ratio. Power Button with Deadman Safety Switch. Forward and Reverse. Built-in LED Lights….Limited 2-Year Manufacturer’s Warranty on Motor, Battery and Charger.
Model LFVL-8
Drill Size 10″
Weight 27 lbs.

3 more rows

How do you cut holes for ice fishing?

  Why does my Ariens snowblower not throw snow far?
Share your love