QUICK START Unpack the 24v Battery Charging Base from carton and plug it in. Slide Battery onto Battery Charging Base using the channels on both sides as a guide. Press down until you hear it click in place. Leave Battery on Battery Charging Base until fully charged (Image 2).
How long is the StrikeMaster Lite Flite?
| Brand | StrikeMaster |
|---|---|
| Manufacturer | StrikeMaster |
| Part Number | LFLD6 |
| Included Components | Lite-Flite Lazer Drill Unit 6″ |
| Size | 6 inch |
How do I contact StrikeMaster? Effective January 1, 2019 Customers should contact StrikeMaster Customer Service toll free at 877-572-7278 or [email protected] for a possible part replacement update at no charge for their Lithium Lazer (LL-8) auger.
How do you use a StrikeMaster auger?
How do you sharpen strikemaster ice auger blades?
How do you start a strikemaster ice auger?
How do you start a strikemaster 24v? – Related Questions
How do you maintain a hand auger?
- Keep blade guard intact when auger is not in use to protect the cutting blades.
- After use, wipe blades dry with a cloth and spray a small amount of oil on cutting edge.
- Check and tighten blade screws before each use to avoid loss of blades due to vibrating during cutting of holes.
Can you sharpen strikemaster Lazer blades?
The frustration of sending lazer blades off to get sharpened only to have them bounce on top of the ice when you get them back isn’t worth it. Buy new and use the old ones as throwing stars to defend your ice house. Strikemaster makes a sharpener for the blades that i used to keep in my tackle box.
How long do ice auger blades last?
Under normal use, blades should be sharpened every 2 to 3 years. Blades must not have been abused drilling into rock, gravel, sand, etc, or until the blades can no longer be sharpened.
Can you hand sharpen ice auger blades?
How do I start a new auger?
How do you start a gas auger?
How deep can you dig with a hand auger?
A hand auger can typically reach depths of up to 30 feet, while a power auger can go much deeper. Once the desired depth is reached, the auger is removed and a pipe is inserted into the hole.
How long does it take to drill a hole with a hand auger?
A manual ice auger with sharp blades easily cuts through 6-8 inches of ice like butter in under 10 seconds. Drilling a hole in ice 10-18 inches thick using a hand auger is significantly harder and will take at least 30 seconds of hard work for each hole. Avoid manual ice augers for ice thicker than 18 inches.
How do you remove rust from an auger?
How much does it cost to sharpen ice auger blades?
Triple Grind Process $29.95 Your cost is $19.95 per set. Select from the drop-down box below. If you are sending in one Jiffy or Strikemaster chipper-style blade, the cost is $13.95. For the rare, Strikemaster Ultramag 9″, 3-Blade Set, cost is $19.95 The Jiffy STX, three blade set is also $22.95.
Can you sharpen auger blades with knife sharpener?
A variety of tools and methods can be employed to sharpen ice auger blades. A blade that has been badly damaged or rusted might first need some attention with a wood or metal file. You can use a whetstone or knife sharpener for precise honing.
How do you sharpen ice auger blades with sandpaper?
How do you sharpen Mora Lazer ice auger blades?
How do you sharpen a post hole auger blade?
Can you sharpen Nils ice auger blades?
Re: Anybody know how to sharpen a Nils auger? Authorized Nils sharpener, as long as they didnt knock it out of angle he will sharpen it sharpe as new or sharper… By all means send it to Frank. He is completely honest and will not charge you if he can not sharpen it due to it being bent.
How do you start an auger?
How do I start a new auger?
How do you start a flooded Eskimo ice auger?
With the unit resting on the ground, squeeze the throttle trigger to wide open throttle or fast position. At the same time the trigger is depressed, pull the starter rope several times, 10 to 15 times back to back. (Flooded engine will usually only take 6 to 8 pulls to get engine started.)
