How do I make a sight fishing hole?

What can I use instead of an ice auger?

Here is a quick list of all the methods I have seen used to successfully cut through ice without an auger.
  • Axe.
  • Spud bar.
  • Digging iron.
  • Pick axe.
  • Chainsaw.
  • Ice saw.

What size ice auger is best? For gas or electric augers, choosing the largest you can afford is usually your best bet. Ten-inch is the most common size and will tackle every situation or species you may target. A 4 1/2 inch hand auger is perfect for chasing panfish during early ice.

Will any drill work for ice auger? Unless you’re using a heavy-duty drill or are unsure of your grip, you’re fine with just using the drill for 6-inch augers. I simply get a good grip on the drill and hold the back of the drill tight with my free hand. But a stabilizing handle isn’t a bad idea for 8-inch models because of increased torque.

What kind of ice auger is best?

  • Best Overall: Eskimo HC40 Propane Ice Auger at Amazon. …
  • Best Budget: StrikeMaster Mora Hand Ice Auger at Amazon. …
  • Best Gas: Jiffy 4G FourStroke Gas Ice Auger at Sportsmansguide.com. …
  • Best Electric: StrikeMaster Lithium 40V Electric Ice Auger at Amazon. …
  • Best Hand Auger: …
  • Best Drill Powered: …
  • Best Hand/Drill-Powered:

Can I use my chainsaw to cut ice? Yes, you can cut ice with your chainsaw. You don’t have to apply any mineral oil to prevent the water from pollution. To prevent the blade from rusting, you will have to look after your chainsaw.

How do I make a sight fishing hole? – Related Questions

How do you cut a hole in a thick ice?

How deep are ice fishing holes?

The hard part is finding them. Many hardwater anglers spend far too much time fishing over deep structure-underwater points and reefs in the middle of the lake in 80 to 100 feet of water. Instead, it’s much wiser to drill holes over and around structure in moderately deep water of 20 to 40 feet.

What is the fastest ice auger?

Trophy Strike 120V Lithium Ion Ice Auger

As far as we can tell, the Trophy Strike 120V Lithium Ion Ice Auger is the fastest ice auger in the world!

Is 6 auger big enough?

I’m content with the 6. Unless your purposely targeting trophy fish a 6 inch hole is plenty especially if you only target panfish. With over 18 inches in diameter when’s the last time you pulled a fish larger than 18 inches in diameter through the ice.

Can you use a hammer drill for ice auger?

What’s the best drill to use for ice fishing?

Can you use an impact driver for ice auger?

so if you own a hammer drill, put it on drill mode and use your auger. using an impact driver will not work on ice.

How do you sharpen ice auger blades?

How long does an ion ice auger battery last?

From the Ion FAQs page: “The battery is expected to last about 600-800 full charge cycles before performance will be affected.” If you exceeded that in two years, you must live pretty far north!

How do you use an electric ice auger?

Can you cut ice with a Sawzall?

Can you use an electric chainsaw to cut ice?

Electric chainsaw is not much more than a glorified limb trimmer. It will cut thicker ice but it will be slow and I guarantee the entire time you will be wondering why you didn’t just buy a gas powered saw. They cost about the same to.

How many hours does a Stihl chainsaw last?

about 2,000 hours

How Long Do Stihl Chainsaws Last? Information we found online suggests that Stihl Pro Chainsaws have a run time of about 2,000 hours. That means the saw would last you for a minimum of 5.5 years before dying. Keep in mind this time is rated for professional chainsaws and not for regular homeowner saws.

Why do some ice cubes have holes?

The reason is probably most trivial: greater surface area allows for a greater rate of cooling. Holes are a neat way to increase surface area without increasing overall dimensions of the ice cube.

What is the best month to ice fish?

March is my favorite month for ice-fishing. The days are longer, the weather isn’t as cold, and the fish like to get caught in March. Following are some things to keep in mind to catch more fish through the ice until the end of the ice season.

What is the best time to ice fish?

How do I make a sight fishing hole?

The best time of day to ice fish is during the first couple of hours after sunrise, and for about 2 hours both before and after sunset. These are the times when most fish are heading to their feeding grounds, and when most species are active.

Is it better to ice fish in shallow or deep water?

For the most part, where you find the fish in the spring and fall will be the same place you’ll find them in the winter. In my experience, I’ve found that most of the best ice-fishing action comes in water from 3-to-20 feet deep.

Do electric drill ice augers work?

Are Eskimo ice augers Made in USA?

With a name like that, you might think Alaska or Canada. Actually, Eskimo Ice Fishing Gear and Ion Electric Ice Augers are made by a company headquartered in Cumberland, Wisconsin, just an hour from Eau Claire.

Where are Jiffy ice augers made?

Jiffy is a proud American-made company. Ben Walker, production team member for 5 years, proudly builds quality and toughness into every Jiffy product so anglers can enjoy their weekends on the lake fishing.

Should I get a 6 inch or 8 inch ice auger?

Is a 6 or 8 ice auger better?

If your going with the hand auger I would recommend the 6 . Its alot easier to punch a bunch of holes with the 6 . Depending on the amount of ice you chew through a season,the 8 inch I always had the replace twice a year. The 6 inch cut better and I went through a set of blades in about a season and half.

What size auger do you use for a 4×4 post?

6″ diameter

Post Holes- If you plan to secure your posts with cement or by tamping dirt, you will need spacing around the post to do so. For example: A 4×4 post (actual size 3.5″x3. 5″) has a maximum width of just over 5″ (diagonally). Therefore, the 4×4 post will likely fit into a hole drilled by a 6″ diameter auger.

How do you make a homemade ice auger?

How do you make an electric ice auger?

How do you turn a hand auger into a drill auger?

How do you convert a hand auger to a drill?

  How do you dig a hole in an auger?
Share your love