The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.
What is the best tool for digging post holes? You can use a post hole digger or power auger to dig the hole. A post hole digger is a manual tool and will get the job done in average soil. If you have hard, rocky soil or a lot of roots – you may want to opt for a power auger.
What is the best fence post digger?
- BEST OVERALL: Southland SEA438 One Man Earth Auger.
- BEST BANG FOR THE BUCK: XtremepowerUS 1200W 1.6HP Electric Post Hole Digger.
- UPGRADE PICK: Landworks Earth Auger Power Head Steel 6″ x 30″ Bit.
- BEST MANUAL: AMES 2701600 Post Hole Digger with Hardwood Handle.
How deep can a manual post hole digger go? Post hole diggers have a maximum effective depth of about 3/4 of their handle length, so a five foot pair will dig about 3 1/2 half deep. Very hard earth like clay is extremely difficult to dig with a manual pair of post hole diggers.
Do post hole diggers work? Digging holes for fence posts or footings requires a different tool because the holes should be deep and cylindrical with sides that are flared at the bottom. A clamshell digger (also called a post hole digger) is a good tool for this type of work.
How deep should a post hole be? Project Instructions Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
How deep is a 10 foot post hole? – Related Questions
How do you dig a post hole in hard dirt?
- Step 1: String your line and pound the stakes. …
- Step 2: Carve out a soil divot with a spade. …
- Step 3: Loosen earth with a tile shovel. …
- Step 4: Use your clamshell digger. …
- Step 5: Use a reciprocating saw on large roots. …
- Step 6: Dislodge rocks with a digging bar. …
- Step 7: Tamp the soil with the other end.
Should I use an auger or post hole digger?
Post hole diggers focus on one task – they dig holes for posts, whereas a hole auger is suited for a wide variety of tasks around the garden. Post hole diggers rely on more work than a hole auger, these heavy hand tools are basically thrown hard into the soil with force then lifted out.
Is a post hole digger worth it?
While that won’t make a lot of difference if you have loamy, soft soil to begin with, for those who have hard-packed clay soils it certainly does. If your soil is very solid, or has a lot of rocks, a post hole digger is an essential tool to have.
How big of a hole do you need for a 4×4 post?
The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter.
Will an auger cut through roots?
The most effective method of installing a post through a root is to drill through it. There is a power tool available known as an auger that will drill through the root, and allow you to put the post right where you need it.
How long does it take to dig a post hole with an auger?
Augers are available for rent at tool rental centers at a cost of around $60 a day. Power augers can dig as many holes in an hour as a post hole digger can dig in eight hours, with hole sizes ranging from 6” diameter holes and up.
Can you put dry concrete in a post hole?
How deep should you bury an 8 foot post?
How Deep Should a Fence Post Be? For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone. For gateposts, you’ll need concrete too.
How do I keep my post level while concrete dries?
You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.
Is it easier to dig in wet or dry dirt?
Soil that’s turned over when wet will form clods that will be very difficult to break apart later, Trinklein said. This is because wet soil is more easily compacted than dry soil. He recommends the “baseball test” before you start digging.
How do you dig a 3 foot deep hole?
How do you make post holes dig easier?
How many bags of cement do I need for a fence post?
1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.
Should fence posts be set in concrete?
Concrete provides a strong foundation for wooden fence posts, but can rot them more quickly. Setting them in dirt, with or without gravel or crushed rock depending on your soil type, can help the posts last longer before going rotten. You can also use metal fence post anchors to prolong their life.
How deep should a 6×6 post be in the ground?
How deep should a post be in the ground:– in general, a post 6×6 or 8×8 that extend 8 feet or more above ground level should be at least 3 feet deep buried in the ground. Posts that extend 6 feet above ground level should have holes at least 2 1/2 feet deep.
Why do fence posts rot at ground level?
Wood fence posts will rot due to prolonged exposure to moisture in the soil.