Can I use an auger for fence posts?

When it comes to digging fence post holes for a new pasture, augers are the way to go. Whether you’re using a handheld auger or (better yet) a tractor-mounted model, augers significantly speed up and simplify the process compared to manual post-hole diggers.

What size auger do I need for fence posts? A 12-inch auger, best attached to a heavy machine, will create a hole large enough for a 6×6 or 4×6 post and plenty of concrete. Smaller augers, like 4- or 6-inch options, are appropriate for light-duty work (like mailboxes) as well as metal fence posts for chain-link fences.

What size auger should you use for a 4×4 post?

6″ diameter

Post Holes- If you plan to secure your posts with cement or by tamping dirt, you will need spacing around the post to do so. For example: A 4×4 post (actual size 3.5″x3. 5″) has a maximum width of just over 5″ (diagonally). Therefore, the 4×4 post will likely fit into a hole drilled by a 6″ diameter auger.

Do post hole augers work in rocky soil? Augers are very powerful machines with a lot of torque that can throw you like a sack of potatoes if the auger bit encounters a rock or a root. If your soil is loamy or sandy, you too can drill 30 holes in a day’s worth of rental. But rocky ground or heavy clay can stymie even the most powerful auger.

How deep should a fence post hole be?

2 feet

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

Can I use an auger for fence posts? – Related Questions

How deep should a 7 foot fence post be?

How Deep Should a Fence Post Be? For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.

How deep should a 5 foot fence post be?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

What size auger do I need?

To choose the auger that best fits your needs, consider how you’ll use it. If you plan on only using your auger to plant plugs, for instance, then a 2- or 3-inch auger will fit your needs. If you anticipate the need to bury stakes or set small posts, then you may prefer a 4-inch auger or another, larger size.

  What is the best garden auger to buy?

How much concrete do I need for a 4×4 fence post?

A 4″ diameter fence post needs a post hole that’s about 12″ in diameter. The depth below ground should be about 1/3 the height of the post above ground….How Much Concrete For A 4×4 Fence Post?
Depth 50 Lb Bags
10″-14″ 2
16″-22″ 3
24″30″ 4
32″36″ 5

How long does it take to dig a fence post hole with an auger?

Augers are available for rent at tool rental centers at a cost of around $60 a day. Power augers can dig as many holes in an hour as a post hole digger can dig in eight hours, with hole sizes ranging from 6” diameter holes and up.

How deep can a one man auger dig?

The available depths for an auger are generally 3 and 4 feet–but there are augers that exist that allow you to drill with more width and depth. Those wielding a one-man auger shouldn’t use it for any holes exceeding 8 inches in diameter. Whereas two-man augers get the job done for a maximum of 18 inches in diameter.

Should I use an auger or post hole digger?

Post hole diggers focus on one task – they dig holes for posts, whereas a hole auger is suited for a wide variety of tasks around the garden. Post hole diggers rely on more work than a hole auger, these heavy hand tools are basically thrown hard into the soil with force then lifted out.

What is the easiest way to dig a post hole?

There’s no question about it — the fastest and easiest way to dig post holes is to use a gas-powered earth auger. Fill the tank with gas, position the auger on the ground, fire it up, hold on tight and watch the soil come streaming out of the hole.

How do you dig fence posts in hard ground?

How to Dig a Hole: Pro Tips
  1. Step 1: String your line and pound the stakes. …
  2. Step 2: Carve out a soil divot with a spade. …
  3. Step 3: Loosen earth with a tile shovel. …
  4. Step 4: Use your clamshell digger. …
  5. Step 5: Use a reciprocating saw on large roots. …
  6. Step 6: Dislodge rocks with a digging bar. …
  7. Step 7: Tamp the soil with the other end.

Can an auger go through gravel?

Hold the auger firmly with both hands. Press the trigger throttle slowly to start the auger turning and to begin drilling through the gravel and soil. Apply downward pressure as the auger turns.

Should fence posts be set in concrete?

Can I use an auger for fence posts?

Concrete provides a strong foundation for wooden fence posts, but can rot them more quickly. Setting them in dirt, with or without gravel or crushed rock depending on your soil type, can help the posts last longer before going rotten. You can also use metal fence post anchors to prolong their life.

  How deep can you go with a post hole auger?

Why do fence posts rot at ground level?

How do you dig a post hole in hard dirt?

Wood fence posts will rot due to prolonged exposure to moisture in the soil.

How do I keep my post level while concrete dries?

You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.

How far apart should fence posts be set?

How far apart should fence posts be set?

Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.

How do I make sure fence posts are in line?

How long do wooden fence posts last?

While treated timber posts can last from anywhere between 10-15 years, untreated timber may need replacing in under 5 years. What’s more, rotting, splitting and warping (where the post expands upon water absorption) are all very common occurrences for wooden fence post systems.

How long should posts be for a 6 foot fence?

Calculate the post lengths If you’re setting wooden or concrete posts in concrete you’ll need 8ft (2.4m) posts for a 6ft (1.828m) fence – i.e. your posts are 2ft (0.6m) longer than the fence height. Use 4in x 4in posts for fences of 5ft and over and 3in x 3in posts for anything under 5ft.

How long does concrete take to set in a post hole?

Typically, you can apply some weight to the posts after 4 hours, but it’s a good idea to wait at least 24 hours before resuming fence construction. Standard concrete mixes may take up to two hours to set and should cure for 24 to 48 hours before any forces are applied to the posts.

How do I put a post in the ground without concrete?

There are a few options for materials to set your fence posts if you aren’t using cement. These include dirt, gravel, sand, and crushed rock. Dirt: Filling the hole with dirt and compacting it will help to support the fence post. However, this method is not very strong.

Is an 8 inch hole big enough for 4×4 fence post?

Is an 8 inch hole big enough for 4x4 fence post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.

  How much can one man dig in a day?

How big of a hole do I need for a 6×6 post?

10″-diameter

A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage.

How big of a hole do I need for a 4×6 post?

For a six-foot-tall post, therefore, you would dig a hole two feet deep. The ideal diameter, meanwhile, should measure three times the width of the post. So, for a standard 4×4, the ideal hole would span twelve inches across.

How deep should a concrete fence post be in the ground?

How deep should a concrete fence post be in the ground?
2 foot

Dig your hole to the correct depth, allowing for the height of the fence panel and the gravel board. As a rough guide the hole should be a minimum 1/3 the height of the fence, so a 6 foot fence would need an 8 foot post in a 2 foot deep hole. Similarly, the hole should be three times the diameter of the post.

How do you install a 4×4 post in the ground?

How many bags of quikrete do I need for a fence post?

Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post.

Is an 8 inch hole big enough for 4×4 fence post?

Is an 8 inch hole big enough for 4x4 fence post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.

What size auger do I need?

What size auger do I need?

To choose the auger that best fits your needs, consider how you’ll use it. If you plan on only using your auger to plant plugs, for instance, then a 2- or 3-inch auger will fit your needs. If you anticipate the need to bury stakes or set small posts, then you may prefer a 4-inch auger or another, larger size.

How big of a hole do I need for a 6×6 post?

10″-diameter

A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage.

How big of a hole do I need for a 4×6 post?

For a six-foot-tall post, therefore, you would dig a hole two feet deep. The ideal diameter, meanwhile, should measure three times the width of the post. So, for a standard 4×4, the ideal hole would span twelve inches across.

Share your love